Вернуться   Форум Pilot Engineering > English forum > Click here :) > Pilot VAF/MAF converter

Ответ
 
Опции темы Опции просмотра
Старый 03.07.2016, 07:03   #11
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

Hi Pin
Part numbers are 0280217124
1433565

cheers
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 08:14   #12
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

I am no longer getting a converter out voltage.
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 10:25   #13
Pin
Супер-модератор
 
Аватар для Pin
 
Регистрация: 08.09.2009
Сообщений: 3,079
Pin на пути к лучшему
По умолчанию

Hi Rohan
Цитата:
Part numbers are 0280217124
1433565
It is bosch hfm5 and it needs ref 5V.
You can get it from 2-nd pin of service connector of the converter or from throttle position sensor ref pin.

Цитата:
I am no longer getting a converter out voltage.
Dont worry, let me know whats happen ?
Can you connect to the converter via bluetooth and read data?
Is LED on bluetooth hc-06 blinking when you power on the converter?
What is postion of jumper ( motronic/jetronic) ?

Последний раз редактировалось Pin; 03.07.2016 в 10:32.
Pin вне форума   Ответить с цитированием
Старый 03.07.2016, 11:06   #14
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

Hi Pin

First up I grabbed the 5v from the vaf sensor, should I take this from the pcb/converter board?

Yes I can connect it to the Bluetooth and read everything, yes the led on hc-06 is blinking happily.
As for the jumper I have tried both, thinking that was the problem, with it connected to pcb and jetronic mode, also disconnected motronic mode.

Regards Rohan
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 11:42   #15
Pin
Супер-модератор
 
Аватар для Pin
 
Регистрация: 08.09.2009
Сообщений: 3,079
Pin на пути к лучшему
По умолчанию

Hi Rohan
Цитата:
First up I grabbed the 5v from the vaf sensor, should I take this from the pcb/converter board?
It is ok to take it from VAF


Please install jumper to motronic position (1-2)
and check voltage with a multimeter between ground and jumper - there should be 5v. If there is no 5v let me know.
If it is ok, then disconnect converter's output from ECU and upload next table to converter( don't forget to save your table before it).
After that please check voltage between output and ground there should be ~2.55v
Let me know a results
Regards
Вложения
Тип файла: tab test.tab (392 байт, 360 просмотров)

Последний раз редактировалось Pin; 03.07.2016 в 11:45.
Pin вне форума   Ответить с цитированием
Старый 03.07.2016, 12:54   #16
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

Hi Pin

Everything worked except getting 2.55v, I am still getting nothing from converter output.

Cheers Rohan
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 14:29   #17
Pin
Супер-модератор
 
Аватар для Pin
 
Регистрация: 08.09.2009
Сообщений: 3,079
Pin на пути к лучшему
По умолчанию

Hi Rohan
Is converter's output shutt off after firmware upgrade or before it?

Please check next voltages between ground and control points 1-7
with a same table test.tab
Нажмите на изображение для увеличения
Название: IMG_20160703_141405.jpg
Просмотров: 458
Размер:	129.2 Кб
ID:	2026
Let me know a result


Rgards

Последний раз редактировалось Pin; 03.07.2016 в 14:34.
Pin вне форума   Ответить с цитированием
Старый 03.07.2016, 14:57   #18
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

Hi Pin

I have not upgraded firmware.

All checks out except point 2 I'm getting 0.5v and point 7 I'm getting 0.1v
And at point 1 11.9v but the car is not running so expected.

Regards
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 14:59   #19
Rohan
Местный
 
Регистрация: 13.02.2016
Сообщений: 20
Rohan на пути к лучшему
По умолчанию

Should I try firmware upgrade?
Rohan вне форума   Ответить с цитированием
Старый 03.07.2016, 15:13   #20
Pin
Супер-модератор
 
Аватар для Pin
 
Регистрация: 08.09.2009
Сообщений: 3,079
Pin на пути к лучшему
По умолчанию

Цитата:
Should I try firmware upgrade?
No.
Цитата:
And at point 1 11.9v but the car is not running so expected.
it is ok.

Now please check next points and let me know a results
Нажмите на изображение для увеличения
Название: IMG_20160703_141405.jpg
Просмотров: 337
Размер:	141.2 Кб
ID:	2027
Pin вне форума   Ответить с цитированием
Ответ

Опции темы
Опции просмотра

Ваши права в разделе
Вы не можете создавать новые темы
Вы не можете отвечать в темах
Вы не можете прикреплять вложения
Вы не можете редактировать свои сообщения

BB коды Вкл.
Смайлы Вкл.
[IMG] код Вкл.
HTML код Выкл.

Быстрый переход


Часовой пояс GMT +6, время: 19:01.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd. Перевод: zCarot