03.07.2016, 07:03 | #11 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
Hi Pin
Part numbers are 0280217124 1433565 cheers |
03.07.2016, 08:14 | #12 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
I am no longer getting a converter out voltage.
|
03.07.2016, 10:25 | #13 | ||
Супер-модератор
Регистрация: 08.09.2009
Сообщений: 3,083
|
Hi Rohan
Цитата:
You can get it from 2-nd pin of service connector of the converter or from throttle position sensor ref pin. Цитата:
Can you connect to the converter via bluetooth and read data? Is LED on bluetooth hc-06 blinking when you power on the converter? What is postion of jumper ( motronic/jetronic) ? Последний раз редактировалось Pin; 03.07.2016 в 10:32. |
||
03.07.2016, 11:06 | #14 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
Hi Pin
First up I grabbed the 5v from the vaf sensor, should I take this from the pcb/converter board? Yes I can connect it to the Bluetooth and read everything, yes the led on hc-06 is blinking happily. As for the jumper I have tried both, thinking that was the problem, with it connected to pcb and jetronic mode, also disconnected motronic mode. Regards Rohan |
03.07.2016, 11:42 | #15 | |
Супер-модератор
Регистрация: 08.09.2009
Сообщений: 3,083
|
Hi Rohan
Цитата:
Please install jumper to motronic position (1-2) and check voltage with a multimeter between ground and jumper - there should be 5v. If there is no 5v let me know. If it is ok, then disconnect converter's output from ECU and upload next table to converter( don't forget to save your table before it). After that please check voltage between output and ground there should be ~2.55v Let me know a results Regards Последний раз редактировалось Pin; 03.07.2016 в 11:45. |
|
03.07.2016, 12:54 | #16 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
Hi Pin
Everything worked except getting 2.55v, I am still getting nothing from converter output. Cheers Rohan |
03.07.2016, 14:29 | #17 |
Супер-модератор
Регистрация: 08.09.2009
Сообщений: 3,083
|
Hi Rohan
Is converter's output shutt off after firmware upgrade or before it? Please check next voltages between ground and control points 1-7 with a same table test.tab Let me know a result Rgards Последний раз редактировалось Pin; 03.07.2016 в 14:34. |
03.07.2016, 14:57 | #18 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
Hi Pin
I have not upgraded firmware. All checks out except point 2 I'm getting 0.5v and point 7 I'm getting 0.1v And at point 1 11.9v but the car is not running so expected. Regards |
03.07.2016, 14:59 | #19 |
Местный
Регистрация: 13.02.2016
Сообщений: 20
|
Should I try firmware upgrade?
|
03.07.2016, 15:13 | #20 | ||
Супер-модератор
Регистрация: 08.09.2009
Сообщений: 3,083
|
Цитата:
Цитата:
Now please check next points and let me know a results |
||